jamesinc
@Slowbrick, I have a spare set of axles in Sydney. Could rebuild them and swap? The axle place can do it in about 90 minutes.
Slowbrick
Can you do that? I was gunna do them. The v70 ones are bigger than 850 ones though.
AshDVS
Dont rebuild them yourself. It sucks, it's filthy, a bit time consuming if you don't do them regularly or haven't done them before and really annoying.
I rebuilt one of mine last week and simply re-booted and re-packed the other. It wasnt difficult but it was just one of those tasks you'd simply rather farm out.
For the cost of getting them reco'd or even buying reco'd ones and having them sent out, it's not worth doing it yourself.
The place @Jamesinc used is one that was recommended to us - well worth a look.
Rob
Slowbrick;35888 wroteCan you do that? I was gunna do them. The v70 ones are bigger than 850 ones though.
They are all interchangeable but manual ones are beefier.
Slowbrick
Yeh I accidentally popped off one of the boots and holy shit the grease. Definitely not a job im going to attempt.
Today I got the front struts swapped in from the donor car and put my suspension back together. The car is now back on the ground and now I just need to plug everything back in.
Ex850R
It will be a happy day when you get to try it out!
Good work.
Slowbrick
No awd and no lsd. I will be happy with it as it is!
Philia_Bear
WIth good gloves and a parts washer it takes me under an to rebuild a pair of 850 drive shafts
I have done like 100+ pairs in my life though....
I vote for welded front diff for lol factor
Rob
Philia_Bear;35928 wroteWIth good gloves and a parts washer it takes me under an to rebuild a pair of 850 drive shafts
under an hey :)
jamesinc
With bad gloves it takes at least an if not two or three.
Ex850R
It took me , with leather gloves , more than an an to get over the colour an consistency of the grease , eeeek , fukan an !
Slowbrick
I may have accidentally lost the little bread clip that goes on the clutch line. Anyone know where to find one?
clinton
Each to their own, but if your shafts are OK and you are just replacing the boots/grease, I dont think it is a bad a job at all. I buy the 50 packs of gloves, use lots of rags, and now have a bench with a vice (vice is nearly essential). I use many pairs of gloves (I throw them out when dirty to save spreading grease around - they are cheap) and that keeps me clean.
I found that the clamps that came with my latest boot kit were rubbish and came loose after just a few months. Now I use heavy duty cable ties - works a treat :-)
Slowbrick
Well its all together but it doesn't start. I jumpered the starter so it cranks but doesn't start. Not sure what I fucked up. Could it be the pnp switch?
Jamest5r_
If it cranks then the pnp swith is ok as it wouldn't crank otherwise, check the connections to the crank sensor this uses the same shape plug as something else in.that region can't remember what though but easilymixed.
nickm
not cranking with the key? your trusty multimeter
Slowbrick
I tried all of the plugs that fit in that region but I will pull it all apart tomorrow and try again. Are there difference between the auto and manual crank sensors?
Jamest5r_
Slowbrick;36109 wroteI tried all of the plugs that fit in that region but I will pull it all apart tomorrow and try again. Are there difference between the auto and manual crank sensors?
No they are the same but there is some differences between obd1 and 2 flywheels
Slowbrick
Hmm...it only goes on one way.
Philia_Bear
Iirc you need to reverse the pins in the vr sensor plug
This turns the falling wave into a rising wave or vice versa and makes it happy
Also is the cam sensor plugged in?