Also, every time I mention the cost of an exhaust, someone tells me it's a crazy amount, yet every cheaper solution always has come with a catch: it rattles, it's uncoated mild steel, it didn't include the downpipe/reused some of the existing bends, it uses slip joints, it doesn't have a catalytic converter, it only uses a single resonator, I had to take it back three times to get them to adjust it properly, the downpipe isn't braced properly to the bellhousing, or I ran it under the rear axle.
Cal's '85 245_Iced VoVo
I would, increased compression forces the rings out and if they are already weak, so fail. Same with a 16v build, you could flycut the pistons in your car, but it would need a re ring regardless. And there's no point doing an Na build if you don't go higher than stock compression, they will be happy at 11:1 with a tune. Alloy heads dissipate heat faster so you can use more compression than you can on my 122s b20 for instance.
Other way around, the 240mm pressure plate with the 235/230mm dished flywheel clutch disc to suit the m46. Dished flywheels get slip issues due to the design. Particularly with turbo builds. You can use it on an Na build, the lighter flywheel is an advantage for a start, about 15kg vs 20kg for the setup James has.
Other way around, the 240mm pressure plate with the 235/230mm dished flywheel clutch disc to suit the m46. Dished flywheels get slip issues due to the design. Particularly with turbo builds. You can use it on an Na build, the lighter flywheel is an advantage for a start, about 15kg vs 20kg for the setup James has.
The exhaust a friend had recently made was from end to end and he didn't want to re use any parts supplied other than a stainless straight section, 3" with a supplied muffler and no other issues. Nothing wrong with mild steel in Australia outside of the snow too.
Happy to have a look at your A/C if you need mate. Located in Daceyville.Cal;119404 wroteI'll run the gauntlet as your first customer. If the heater works does that mean it just needs a regas and the compressor is sweet?
Awesome, cars currently sitting on the central coast, i'll hit you up when I get it back to Syd. Thanks heaps!Volvo850;119490 wroteHappy to have a look at your A/C if you need mate. Located in Daceyville.Cal;119404 wroteI'll run the gauntlet as your first customer. If the heater works does that mean it just needs a regas and the compressor is sweet?
Where on the central coast is it located? I could come up and have a look if need be?Cal;119492 wroteAwesome, cars currently sitting on the central coast, i'll hit you up when I get it back to Syd. Thanks heaps!Volvo850;119490 wroteHappy to have a look at your A/C if you need mate. Located in Daceyville.Cal;119404 wroteI'll run the gauntlet as your first customer. If the heater works does that mean it just needs a regas and the compressor is sweet?
20 days later
In regards to clutch replacement options I found an 8.5" HD exedy clutch, suited for a flat flywheel.
According to an Anthony Hyde article:
"INTRO - All early model 240's (1977-85) with mechanical K-Jet fuel injection used a flat flywheel with a clutch disc diameter of 8.5"
http://people.physics.anu.edu.au/~amh110/Clutch/clutch_upgrade.htm
This should work should it not?
If it does the affordability appeals to me for this build, I can stick with the original fly.
According to an Anthony Hyde article:
"INTRO - All early model 240's (1977-85) with mechanical K-Jet fuel injection used a flat flywheel with a clutch disc diameter of 8.5"
http://people.physics.anu.edu.au/~amh110/Clutch/clutch_upgrade.htm
This should work should it not?
If it does the affordability appeals to me for this build, I can stick with the original fly.
Yes, probably
That it literally the clutch I offer on a redrilled flywheel...
2 months later
- Edited
On Tuesday night we loaded up my brothers Forrester to begin a round trip from Sydney to Meredith Music Festival. As we neared Wollongong his clutch started giving up on the hills so we turned back to Sydney and much to my pleasure loaded up the Volvo (with what I would guess was 500kgs of luggage, beer and human) and set off again for our second attempt that same night.
2400kms later I returned to Sydney prouder than ever, albeit a tad fried from 3 days partying and 12 hours driving with no overdrive. The only issue that arose was a loose calliper that I was able to repair thanks to some advice from Bruce.
Volvo for the win.



2400kms later I returned to Sydney prouder than ever, albeit a tad fried from 3 days partying and 12 hours driving with no overdrive. The only issue that arose was a loose calliper that I was able to repair thanks to some advice from Bruce.
Volvo for the win.



She looks as beautiful as ever mate. Would love to come have a look at the overdrive for you.
I'm happy to pitch in overdrive skills. I have at least one functional AW70 gearbox that I don't want.
I finally found the fault, after resoldering the relay probably unnecessarily and checking the wires in the cabin and gear lever I went under the car and found one of the plugs that sleeve over the terminals on top of the transmission to be completely dissintergrated. Was thinking I can just cut the end off and crimp the wire around the little nipple thang and tape it up...jamesinc;126179 wroteI'm happy to pitch in overdrive skills. I have at least one functional AW70 gearbox that I don't want.

Shitty picture, at least it gives you an idea of how fiddly it is reaching blindly up there
- Edited
If you want to make life a lot easier, drop the rear cross member and tilt the gearbox down. Just wedge a towel between the head and the firewall so you don't scratch anything.
If you rewire it, get some adhesive heatshrink from jaycar and cover the entire wire, it should stop it degrading further.
If you rewire it, get some adhesive heatshrink from jaycar and cover the entire wire, it should stop it degrading further.
Fuck, thank you so much mate, saving me a lot of headache as usual.jamesinc;126188 wroteIf you want to make life a lot easier, drop the rear cross member and tilt the gearbox down. Just wedge a towel between the head and the firewall so you don't scratch anything.
If you rewire it, get some adhesive heatshrink from jaycar and cover the entire wire, it should stop it degrading further.
a month later
So I painted my car with Rust Guard on the weekend....

Was going for a pale pink but has turned out looking more white than anything. Probably for the best as I imagine i would grow tired of approaching a pink car every day.
I got 4 litres of paint mixed up from Bunnings for $100, added 200ml thinner ($40) to every 700ml paint.
Supercheap auto has a ridiculous deal on gravity fed spray guns at the moment at $25 reduced from 80.
After cutting out the rust, a little rust converter and some bog I followed the steps in the below link fairly closely, I just didn't polish it at the end as i'm enjoying the flat finish for now.
http://forum.jdmstyletuning.com/showthread.php?55335-The-140-paint-job
I ended up doing 3 coats everywhere except for any upward facing surfaces (bonnet, roof) where I would do a fourth as the original paint was fairly warn in these spots.
I've said before, I don't want a show car, i've owned tidy cars before and don't enjoy them as much so didn't spend a huge amount of time on preparation, for example there was still clear coat in some areas. Still the paint feels pretty tough, i reckon it will get grubby especially with flat finish so when/if that happens i'll just hit it with a wet sand.








Was going for a pale pink but has turned out looking more white than anything. Probably for the best as I imagine i would grow tired of approaching a pink car every day.
I got 4 litres of paint mixed up from Bunnings for $100, added 200ml thinner ($40) to every 700ml paint.
Supercheap auto has a ridiculous deal on gravity fed spray guns at the moment at $25 reduced from 80.
After cutting out the rust, a little rust converter and some bog I followed the steps in the below link fairly closely, I just didn't polish it at the end as i'm enjoying the flat finish for now.
http://forum.jdmstyletuning.com/showthread.php?55335-The-140-paint-job
I ended up doing 3 coats everywhere except for any upward facing surfaces (bonnet, roof) where I would do a fourth as the original paint was fairly warn in these spots.
I've said before, I don't want a show car, i've owned tidy cars before and don't enjoy them as much so didn't spend a huge amount of time on preparation, for example there was still clear coat in some areas. Still the paint feels pretty tough, i reckon it will get grubby especially with flat finish so when/if that happens i'll just hit it with a wet sand.







Wow, great budget DIY paint job! :)
Ha that's excellent. Love the recycling of wrapping paper.
Sweet job you have done there well done and liking the colour