SPT940's 960 wagon

SPT940 · 2014-02-17T08:50:40+00:00

So berry didn't have a bonnet or rack for you? Where Melbourne are you located?

iceton1975

I can help with s/h cat and sensors 0434 897144

asiandriver

SPT940;20132 wroteOn with rebuilding the headlights before installation. Swap over lense to new bucket and give a thorough clean.

This would be a good time to fit headlights with electric beam angle adjustment motors if you're interested, as the headlight buckets for manual & electric adjusters are different. 960's from 1995 onwards are pre-wired.

SPT940

I ended up doing a little more massaging of the radiator support panel. I noticed a shape on the inner guard behind the large white plastic cap. To me, it looks as though this is a factory fold as it is very straight. I hope so.

I'm now going to sand and clean up the battery floor panel, prime and undercoat it and repaint it, as well as the radiator support panel. I need to do a little more flattening too. I hate leaving something that I can make better.

I appreciate the offer of the headlight angle motors, but right now i'm at the end of my tether over this. It's been a frustrating weekend.

The bonnet was a disappointment, although I was half expecting it as I've had experience with Taiwanese guard on my "Z". Ended up throwing it in the scrap and getting a good second hand one and stripping it back. So I'll have to go down that route with the bonnet.

Managed to get the front plastic mud flaps on too. They were missing, so got some used ones from the pick and pull. I used scrivets instead of the factory rivets. It's ok, but I'll probably get some rivets down the track.

I was looking at the bluetooth OBDII apps again. Not sure which are the best. Like to link it up to an iPad mini mounted in front of the radio in a clear acrylic mount, but thats a project for another day.

Aussie240

Any updates?
I need some inspiration for my 960 sedan, thinking if selling up :(

Vee_Que

There aren't many in Australia but lots of modified ones in europe and America. Maybe an inspiration thread is needed.

SPT940

I reckon I might need a bit more inspiration! I still haven't got around to buying the O2 sensors and a secondhand CAT. Slack, I know!

If they were presented to me I would gladdly buy them - I'm getting lazy in my dotage!

Just like to get it running again. That would be inspiration enough.

It is all straight, and awaiting paint for the radiator support panel, etc.

The seconhand bonnet can come later too.

I am seriously on the trail of filling a pallet in the U.S. with all of the gear I'm after, and backloading it onto a friends container. If only he would organise it. I do need to get onto that.

I keep seeing awesome wheels in 17" & 18" and even 19", but I will probably hang out for Pegasus 18" or 19" in the end.

These might work?!?!?

Maybe this weekend I will get the CAT & Sensors, along with the 940 Headers that I have to pick up!!!!!

SPT940

or theses:

Perhaps powdercoated in Gun Metsal Grey. and Pacific Blue Nautic detailing!?!?!?

Could look nice colour coded to the Pacific Blue Nautic!!!

SPT940

I know they're 4 stud, but, they do come in 5 x 108 ET 40 18".

SPT940

....or these....

SPT940

Come on, inspire me to finish!

Vee_Que;23950 wroteThere aren't many in Australia but lots of modified ones in europe and America. Maybe an inspiration thread is needed.

Vee_Que

A pallet from the states eh? I'd be after a v90- rear bumper and am buying a spoiler, just need it in the right spot for said container!

SPT940

I'll have a chat to you about that. Can you help with the CAT & 2 sensors?

Vee_Que

I can recommend an exhauast shop or a mate to do it. And sensors. Yes. Fcp Groton new.

iceton1975

Like I said to you, I can help with cat and sensors, wrecked 3 in the past 4 months

Philia_Bear

T6 motor
Doooo-eeeet

« Previous Page