1977 244DL "Amy"

jamesincJames (@jamesinc) Oz Volvo Ice Fortress
edited July 2017 in RWD 8211 / 440joined Jul 2013

Foreword: Honourable mention - 1984 240GL, "Graham"

So back in Febuary/March 2013 I was looking around for a restoration project. I found a mid-80s 240GL that sounded like fun. It was a total beater, had been sitting in a field out since 2006. I bought it for $100-odd dollars, and @JonBot conveniently towed it down to Sydney. Didn't have any rust, bodywork was nice and straight. "Clutch is slipping".

Cleaned the distributor, put new plugs on it, and boom, got her running. K-Jet is some seriously solid engineering. Cleaned all the nests out of the engine bay, under the upholstery, even in the gap between the fuel tank and the boot floor! It was full of nasty rural-spec spiders, so I bombed the car.

Now I stupidly didn't take any photos of this next bit, but long story short we pulled the motor out to address the clutch issue... and found a virtually brand-new clutch. So what was that grinding sound? Turns out it was bits of second gear rattling around the gearbox. So at this point I had had enough of this car. I bought it kind-of by accident, and it was the most uninspiring 240 ever made, and now I'd have to source a new M46 gearbox. Well to hell with that! We gave it a paint job before it was taken to the wreckers:

I stripped it for useful parts and then it was gone. Poor Graham, it was simply not to be.

Chapter 1: Finding Amy

Brendan put the word out on Turbobricks that someone in the NSW club had an early 244 going for free. I was keen to this time find the right Volvo for my project, so I got the owner's details and gave him a call. Lovely guy by the name of Alan down in Sans Souci. It was a 1977 244DL in sky blue. He bought it new in 1977. It started and ran, but hadn't been driven since 2011 (judging by the rego sticker). It had a few bits of rust (how little did I know) but otherwise looked to be very clean and original, and it was cool in every way - first-generation 240, flathood, dodgem car bumpers, classic Volvo steelies, good brightwork. Winner!

Chapter 2: Rust

Now, I knew it had some rust. There was a bit of bubbling in the corner of the windscreen, a bit behind the rear wheel arch on the driver's side, and a bit below the driver's tail light. The rear passenger door was a total goner and would need replacing. But, I wanted a project, I wanted something that would allow me to get better at bodywork, and this seemed like just about the right amount of work.

Chapter 3: Rust exploration

So having identified those initial problem areas, I set about doing a more detailed inspection of the bodywork. There were many suspect areas where the paint damaged and perforated, but nearly all of them turned out to be tiny specs of surface rust. So I just sanded the rust out, treated the metal and put some primer over it.

This lower front bar has some holes in it... I'm still on the lookout for a replacement.

The rear passenger door was a total goner, so it was out with the old, and in with the new, courtesy of Berry Motor Group.

Much better.

Chapter 4: Project windscreen

The bubbles around the windscreen meant that the windscreen needed to come out. Brendan and I got it out in a few minutes with a length or wire and a box cutter.

Lordy. Many of the windscreen surround retaining clips were broken, and after initially despairing that they might be impossible to replace, I found they were still available OEM! Thanks Volvo! So after too much time with a rag and bottle of kerosene, I had the old butyl sealant rubber removed and everything cleaned up.

... and with the clip out...

... and cleaned...

Then some grinding, some magic and some POR15 occurred, and the end result is this:

Chapter 5: Project welding things

Brendan helped me out a lot with welding. I hadn't done any serious bodywork repairs before this car, so I needed someone to show me the way, as it were.

Part I: Wheel arch

You saw the rust in one of the pictures above. Well, we cut off the outer skin and, using a cut I had taken from @Spac's scrap car, we replaced it:

That's more or less how it sits now. I need to do some final grinding of the welds to get everything smooth, then fill it and it's done.

Part II: Rear passenger door frame

Initially I didn't think much of the rust on the door jamb, but as I removed paint and glass I realised it was actually one hell of a rust hole. It seems to have been patched at some point in the past, and this patch has then been filled over with a lot of body filler. Unfortunately, it didn't work, and the rust returned.

Hmm, not great...

Wait a second, that's an awful lot of body filler...

Fuck.

Out it comes!

Making some patch panels

Inner side replaced

I got everything roughly the right shape, then tacked it along one side and bent it into its final position with a hammer.

Getting close...

Welds done.

Attempt #1 to clean it up

Brendan was around yesterday, and went over my welds with higher current, as some of them didn't penetrate fully. I don't have pics of that yet.

Part III: Tail light area

I didn't chose the weld life, the weld life chose me.

Before cutting

After cutting

Parts from the scrapped rear door were used to reconstruct the corner. The curve of the sill was an almost perfect match to the curve at the rear of the car. Luckily it looks like Volvo only ever bought their designer a single set of French Curves.

Brendan helped me with this bit of joinery, matching the original seam and bumper lip, and it looks pretty great.

Part IV: Guttering

The guttering on the passenger side of the car was a total mess. It was badly rusted in many places. Initially I thought it would be very difficult to fix this, but after cutting some good guttering from @Spac's parts car, I decided to take a crack at it, and it ended up working out well. NB: the roof line of pre-78 240s is a different curve to 78+ 240s. I had to tack a few inches of the guttering at a time, then bend it into shape, until I had the whole lot in place.

Chapter 6: Filling and contouring

The chapters are a bit out-of-sync at this point as there's one or two rust-related bits still to come.

I decided to start filling over the patch panels and getting the bodywork all good and straight. The first off the bat was the wheel arch.

(TODO: add photo of wheel arch with filler)

Next was the rear passenger door frame area.

I'm still not 100% sold on the curve. Going to wet it tonight and see what the reflection looks like... Either way though it's damn close, it might just be a job for some high-fill primer.

«13456720

Comments

  • TigabuTiga (@Tigabu) Sweet Home Norwoodama
    1893 / 38joined Jul 2013

    Love the bug-bomb holder you have there, James :)

    "Patriotism is the last refuge to which the scoundrel clings, steal a little and they trow you in jail, still a lot and they make you a king" ~ Robert Zimmerman
    1978 264 'The Lady Syrah' PRV 2.7 BW35
    1978 245 'Spike' B21 M46
    1980 242GT 'Skiten Lådbils' B230 M47
    [GONE TO SCRAPPY HEAVEN] 1988 240 Wagon 'The Goon' B230 M47
    [GONE TO TEENAGE DELIRIUM]1985 240 Wagon 'The Cowabunga Mobile' B230 M45
    _____________________________________________
    Tiga Bu resides in a fairytale
  • jamesincJames (@jamesinc) Oz Volvo Ice Fortress
    8211 / 440joined Jul 2013

    I would appreciate it if someone would buy this 244DL so my 244 can be friends with it.

  • TigabuTiga (@Tigabu) Sweet Home Norwoodama
    1893 / 38joined Jul 2013

    That would be ace...

  • jamesincJames (@jamesinc) Oz Volvo Ice Fortress
    8211 / 440joined Jul 2013

    Oh yeah informally the plan with the 244 is to re-paint it in 1K to the original sky blue. I'm having a hard time getting an exact colour code for it, as it's not written on the VIN plate. I may have to get a clean bit of metal colour-matched.

  • A_Volvo_DriverScott (@A_Volvo_Driver) Victoria, The Revenue State
    2811 / 30joined Jul 2013

    A great story mate! I would assume that most of us here have interesting stories like this :)

    1985 240 Wagon Henrik aka "Hank" - build thread in progress
    1984 240 GLE Sedan "The Moose"
    1992 240 GL Wagon "The TURD"
    1997 Fairlane by Tickford "The Tickford"

    Tarneit? Where is that?
  • 61 / 13joined Jul 2013

    Great work! Keep it up, It's great to see a growing scene of restoring old series 244/242

  • jamesincJames (@jamesinc) Oz Volvo Ice Fortress
    8211 / 440joined Jul 2013

    I started on body filling last night, will post a proper update soon. Takes a fair few goes to get the contouring right tell you what!

  • TigabuTiga (@Tigabu) Sweet Home Norwoodama
    1893 / 38joined Jul 2013

    "If it was easy, everyone would do it." Sensei Raoul :D/

  • jamesincJames (@jamesinc) Oz Volvo Ice Fortress
    8211 / 440joined Jul 2013

    Updates above!

  • TigabuTiga (@Tigabu) Sweet Home Norwoodama
    1893 / 38joined Jul 2013

    Looks mighty!

  • jamesincJames (@jamesinc) Oz Volvo Ice Fortress
    8211 / 440joined Jul 2013

    More updates! Finally got around to doing the rust at the top of the boot. I drilled out the old spot welds to separate the two panels, then cut them separately. I then welded patch on to both, and very carefully using a thin cutting blade on the grinder removed the excess weld from the joining surface. Finally I clamped the two pieces together and spot welded them, then shot WD40 in between the panels as best I could.

  • jamesincJames (@jamesinc) Oz Volvo Ice Fortress
    8211 / 440joined Jul 2013

    Okay so the first version of the rear corner was terrible. It sloped far too much inward, and was obvious after I test fitted the rear bumper and trim. So I cut the bottom out of it and re-did it! The size of the gaps gives you a bit of an idea of how much further I had to knock it out.

    I also decided that replicating the panel seam properly was too much effort and instead am going to fill the seam on both sides of the car.

    That same day I also tackled the additional rust I found on the other side of the lip. Bloody rust! I am yet to clean that bit up as it got dark and cold. What a cracker of a day though! Sunny 22 degrees. If this is winter, summer is going to be an absolute scorcher!

    Chased so many holes...

    I also had a rag in the boot with some prepwash on it, and set that on fire by accident. Whoops!

  • jamesincJames (@jamesinc) Oz Volvo Ice Fortress
    8211 / 440joined Jul 2013
    I am down to the last bit of rust repair! I've also started to prep the car for manual conversion. Gear selector is out, and the underside of the car got an extensive degrease and power wash to make things a bit less oily.
  • 5919 / 174joined Jul 2013
    Looking good James. Are you redoing the rust protection underneath in something lighter or even more awesome than stock? @zzdhalla should be able to point you in the direction of the appropriate thing.
  • jamesincJames (@jamesinc) Oz Volvo Ice Fortress
    8211 / 440joined Jul 2013
    Underneath is mint, no need to do anything. Or do you mean I should strip the underside?
  • 5919 / 174joined Jul 2013
    Strip if you are keen but just to cover where you have done work if you aren't. Like that butt cheek.
  • RobRob (@Rob) - Lockyer Valley, SE Qld
    5696 / 531joined Jul 2013
    Looking good. i fear the rust repairs i need to do. i guess tackle them 1 spot at a time and it will be fine.
    ________________________________________________
    Current: 1966 120 wagon, 1970 162, 1973 164E + supercharger, 1998 C70 T5 AWD Coupe, 2009 XC70 D5 LE
    Previous: 1979 242GT, 1980 262C, 1984 265GLE, 1985 740T, 1996 850R, 1996 850AWD .... among others
  • jamesincJames (@jamesinc) Oz Volvo Ice Fortress
    8211 / 440joined Jul 2013
    This door is the donor for patch panels. It illustrates how much rust was cut out

    O8kwM9Bl.jpg
  • jamesincJames (@jamesinc) Oz Volvo Ice Fortress
    8211 / 440joined Jul 2013
    And officially the last patch panel is done!

    lEqP6jHl.jpg

    2JFVCaZl.jpg
  • jamesincJames (@jamesinc) Oz Volvo Ice Fortress
    8211 / 440joined Jul 2013
    After 7 months spent doing body restoration, it's finally time to get down and dirty with the mechanicals!

    60YZhuhl.jpg
Sign In or Register to comment.